The NACE NACE-CIP1-001 Questions & Practice Test are Available On-Demand [Q33-Q53]

4.5/5 - (2 votes)

The NACE NACE-CIP1-001 Questions & Practice Test are Available On-Demand

Valid NACE-CIP1-001 Exam Dumps Ensure you a HIGH SCORE

For more info read reference:

The certification path of the NACE CIP1-001 exam is explained here.

You can get a certification if you pass the NACE CIP1-001 exam. You should not take a risk while choosing the NACE CIP1-001 certification. We are offering you the best NACE CIP1-001 exam dumps. The NACE CIP1-001 exam is designed by experienced professionals. They have written different kinds of questions on the topic related to the NACE CIP1-001 exam.

QUESTION 33
The least effective method of surface cleaning is most likely

water blasting.

dry grit blasting.

hand tool cleaning.

power tool cleaning.

QUESTION 34
If a Thermoset coating is heated it will:

Harden and retain its hardness when cooled

Harden and return to its original hardness when cooled

Soften when heated and return to its original hardness when cooled

Soften when heated and retain its softness when cooled

QUESTION 35
A magnetic pull-off type gauge is a good choice when:

Accuracy is not required

When an intrinsically safe tool is required

Performing an adhesion test

When working on non-ferrous metals

QUESTION 36
Stripe coats are generally applied to:

Edges and corners

Welds

Complex geometric shapes

a), b), and c)

QUESTION 37
If a contractor is using a poorly maintained compressor to supply air for abrasive blast cleaning and conventional airspray, the coating inspector should perform a

dry film thickness (DEI) measurement.

wet film thickness (WFT) measurement.

blotter test for the presence of oil and water.

vial lest.

QUESTION 38
When applying Thermal Spray Coatings the specification is most likely to refence:

SSPC PA 2

NACE SP 0178

NACE SP 0188

SSPC-CS 23.00/AWS C2.23/NACE No. 12

QUESTION 39
The most important factor resulting in improved job site safety is:

Personal Protective Equipment

Engineering Controls

Safety Enforcement

Situational Awareness

QUESTION 40
It is good practice for the NACE Inspector to have instrument calibration certificates available:

At all times

In the office only

In the field only

Only if the specification requires it

QUESTION 41
Conventional spray is a good choice when:

High production rates are required

High quality finishes are required

High transfer efficiency is required

High viscosity coatings are being applied

QUESTION 42
A NACE Coating Inspector is permitted to transport coating material when:

Asked to do so by the Coating Application team

Asked to do so by the Owner’s Representative

The Inspector should never transport coating material

If the Inspector meets all the necessary requirements for Transportation of Dangerous Goods

QUESTION 43
The NACE Inspector should perform tests for soluble salts:

Prior to surface preparation

After surface preparation

Prior to coating application

When specified

QUESTION 44
SSPC SP 1 identifies the use of:

Organic solvents

Inorganic solvents

Biodegradable detergents

A wide variety of materials

QUESTION 45
Removal of welds splatter is required:

On every job

When ISO abrasive blast standards are specified

When NACE/SSPC abrasive blast standards are specified

When specifically identified in the owner’s specification

QUESTION 46
NACE SP 0178 is a standard for:

Structural steel to be coated for Atmospheric Service

Tanks and Vessels to, be Lined for Immersion Service

Stainless steel pipe to be Externally Coated

Tanks and Vessels to be Externally Coated

QUESTION 47
Whenever dissimilar metals must join, the most common practice is to

provide cathodic protection to prevent corrosion,

provide anodic protection to prevent corrosion.

coat all connected dissimilar metals.

avoid coating all connected dissimilar metals.

QUESTION 48
When using a sling physchrometer a very large difference between the wet and dry bulb readings indicates:

High Relative Humidity

Low Relative Humidity

High Surface Temperature

Low Surface Temperature

QUESTION 49
An inspectors personal log book should contain:

Subjective comments re ding the application team

Objective comments regarding the application work

No comments regarding the application team

The inspector’s personal opinions of the application team

QUESTION 50
How many gauge readings does SSPC-PA 2 require within a 4 cm (1.5 inch) diameter circle?

QUESTION 51
You are the NACE Coating Inspector on an exterior job where the contractor is not using any environmental controls, For the last several hours your reading; indicate the relative humidity is rising and the substrate temperature is dropping. The sky is clouding over and the weather forecast is for evening showers. It is now 4 PM, your readings indicate you have minimally acceptable environmental conditions, however if the current trend continues, you expect to be outside specified conditions soon. The contractor advises you he is going to mix up the next full kit to complete his for the day.
Your FIRST preformed course of action is to:

Advise the Contractor he cannot proceed

Advise the Contractor he can proceed

Advise the Contractor of your readings

Call your supervisor

QUESTION 52
Non Conformance Reports are completed by the Inspector:

In every instance that an item does not meet the specification requirements

When the Inspector deems it to be a significant non-conforming item

When the Inspector and Contractor deem it to be a significant non-conforming item

In accordance with the specification’s definition of a non-conformance

QUESTION 53
You are an inspector on a project where SSPC SP 3 is specified.
What sort of tools should you expect the Contractor to use to achieve the standard?

Abrasive blast nozzles

Power tools

Hand tools

Airless spray equipment

Loading …