NO.50 A new web application is being deployed Mutual SSL authentication must be used to authenticate clients.
Which of the following two tasks must be completed to meet the requirements? (Choose two)

NO.51 A new iRule needs to be tested. The LTM Specialist needs to measure page load times and monitor potential changes in memory usage A load test is scheduled.
Which two features should the LTM Specialist use to monitor these requirements? (Choose two.)

NO.52 Which process can be eliminated by terminating SSL communication on the LTM device rather than the backend pool members?

NO.53 AN LIM Specialist must upgrade the VCMP Guest active/standby LTM pair from version 11.3 to 11.5.3 on two VCMP Hosts.
where should the LTM Specialist import the latest 11.5.3 ISO images?

NO.54 Refer to the exhibit.

An LTM Specialist has multiple SNAT and virtual server objects configured as in the bigip.conf shown.
The LTM Specialist tests a connection from a client with. IP 172.163.31.11 to 192.168.0.100:80.
Which two objects will show an increase in Local Traffic statistics connections?

NO.55 An HTTP monitor is created and assigned to a pool with the following non-default configuration:
Interval: 7 seconds
Timeout: 22 seconds
Reverse: Yes
Send String: GET/status.html HTTP/1.1/r/nHost:test.example.com/r/nConnector:Close Receive String: Up The HTTP server sends the following response:

What is the resulting pool status?

NO.56 A web server is being overloaded with HTTPS traffic. To decrease the load on the server, the LTM Specialist and the Server. Administrator decide to perform SSL offloading on the LTM device. The configuration of the virtual server is as follows:

Which change must be made to the configuration to perform SSL offloading?

NO.57 Exhibit.

The three VLANS shown provide connectivity to backend servers. The backend servers are being moved to unmanaged switches and require separate interfaces.
How should the F5 device interfaces be configured?

NO.58 An LTM Specialist needs to apply SNAT using currently used SNAT pool to a new virtual server.
What needs to be completed before applying that configuration change?

NO.59 An LTM device needs to be configured a virtual server. The application requires SSL encryption from the client to the server and an X-Forwarded-For added by the LTM device.
Which virtual server type should the LTM Specialist use?

NO.60 Refer to the exhibit.

The LTM devices LTM3 and LTM2 have four Traffic Groups defined with approximately the sar of failover objects defined in each group.
– Traffic Groups A and C have Default Device set to LTM1
– Traffic Groups Band D have Default Device set to LTM2.
– Traffic Groups B and C do NOT have Auto Failback enabled. Traffic Groups A and D have Auto Failback enabled with a timeout value of 60 seconds.
– Traffic Groups A and D have Auto Fallback enabled with a timeout value of 60 seconds.
Both LTM devices are healthy and able to pass traffic for any Traffic Group.
LTM1 loses connectivity on interface 1.4. The LTM Specialists notified 60 seconds after the interface goes down.
What is the state of the Traffic Groups on each LTM device?

NO.61 A web developer needs a virtual server configured for an application.
The application details are as follows:
Application is accessed on port 443.
The application traffic is encrypted by the server.
HTTP is not being used. No data manipulation is necessary.
Throughput is critical.
NO connections are terminated on the LTM.
Which configuration provides the best performance?
A)

B)

C)

D)

NO.62 The picture belongs to static content, you can configure static content cache in FS to meet this demand An LTM Specialist must configure session persistence for a highly available, highly utilized web-based application.
* The following requirements are provided:
* http proxy setup for security
persistence information available to the HA peer in case of failover
The LTM Specialist needs to minimize additional burden on the LTM device to the greatest extent possible.
Which persistence profile should be used?

NO.63 An LTM specialist needs to upgrade a VCMP quest in an HA Setup with minimum interruption for all VCMP guest instances.
In which should the LTM Specialist perform this upgrade?

NO.64 Exhibit.

– The ITM devices LTM 1 and LTM2 are configured in Device Group X (Sync-Failover)
– LTM3 and LTM4 are configured in Device Group Y (Sync-Only)
– An LTM specialist configures Device Group Z (Sync-Only) to keep several profiles in (sync-Only) to keep several profiles in sync across all devices.
– Device GROUP X has four Traffic Groups A, B, C and D configured.
– Device Group Y has four Traffic Groups E, F, G, and H configured
– Auto Fallback IS NOT Enabled.
– Each Device group is healthy and able to pass traffic for any traffic group assigned to that Device Group.
The data center that contains LTM2 and LTM4 loses power. After 10 minutes; power is restored and all devices are up and healthy.
What is the state of each Traffic Group on each ITM device after power is restored?
A)

B)

C)

D)

NO.65 TWO LTM devices are in the same Device Group and configured for Ac live/Standby Failover. The LTM Specialist observes that the HA Active and Standby device constantly changes state. All network links use the default route domain A dedicated fiber ink is used for the HA connection with a latency of 250 ms but no packet loss.
What is causing the change in failover state to occur?

NO.66 Refer to the exhibit.

The http monitor is applied to a pool All members are enabled One pool member stops responding TCP port 80. The server still responds to ping.
What is the resulting status of this pool member?

NO.67 An LTM Specialist configures a new virtual server with a single pool member. The LTM Specialist has NOT defined a health monitor for the pool, pool member or node.
What is the status of the virtual server?