Q182. Which two QoS mechanisms help prevent congestion on an Aruba CX switch? (Select two)

Q183. A network engineer for a company with 896 users across a multi-building campus wants to gather statistics on an important switch uplink and create actions based on issues that occur on the uplink. How often does an NAE agent gather information from the current state database in regard to the uplink interfaces?

Q184. A Linux SFTP server is configured for IP address 192.168.1.100, and the CX 6325 switch has a management IP address 192.168.1.200.
How can you back up the saved switch configuration to a remote location?

Q185. Which two configuration tasks must be performed when creating a device profile for an AP?
(Select two.)

Q186. Which two overlay technologies are supported on Aruba CX switches? (Select two)

Q187. A network engineer is setting up BGP on AOS-CX switches. The engineer is establishing two different eBGP peering’s to two different service providers. The engineer has dozens of contiguous C-class public networks that need to be advertised to the two service providers. The engineer manually defines the networks to be advertised individually with the “network” command. How can an administrator advertise only a summarized route to the two service providers?

Q188. A network has an ABR that connects area 0 and 1. A network engineer configures a summarized route for area 0. The ABR is a designated router (DR) for the segment it uses to connect to area
1.
Which LSA type is assigned to this route when the summarized route is advertised into area 1 by the ABR?

Q189. An administrator is managing a network comprised of AOS-CX switches deployed at the aggregation layer. The switches are paired in a VSX stack and run the OSPF routing protocol.
The administrator is concerned about how long it takes for OSPF to converge when one of the VSX switches has to reboot.
What should the administrator to do speed up the OSPF convergence of the switch that is rebooting?

Q190. Examine the network exhibit:

Examine Rome r4″s partial OSPF configuration:
router OSPF 1 Area 0
exit interface vlan 100
ip ospf area 0
exit interface vlan 40
ip ospf area 0
exit interface 1/1/1
vlan access 100
mtu9000
Ip ospt hello-Interval 1
Ip ospt dead-Interval 4
ip ospf authentication simple-text
ip ospf authentication-key key123
When executing the “show ip ospf neighbors” command, Router 4 is in a FULL state with Router
3 and Router 2, but a 2-WAY state with Route3.
What is causing the 2-WAY state with Router 1?

Q191. What is correct regarding rate limiting and egress queue shaping on AOS-CX switches?

Q192. Which Aruba Central deployment model provides local configuration control with cloud-based monitoring?

Q193. You are configuring OSPF on each of the devices shown. After verifying the OSPF neighbor table on each, you notice that Router-1 and Access-1 have neighbors in the 2WAY state. What is the reason for this?

Q194. What is correct regarding policy-based routing?

Q195. Which CLI command configures an Aruba CX switch as a DHCP server?

Q196. A network administrator is implementing BGP for a larger network. The network has over 20 exit points across 15 different BGP routers. The administrator does not want to implement a fully- meshed iBGP peering between all BGP routers.
Which feature should the administrator implement to reduce the number of peers the administrator needs to define?

Q197. Refer to the exhibit:

Interfaces 1/1/53 and 1/1/54 were accidentally disconnected from Switch-A, the primary VSX member. Client A is experiencing network disruptions with network connections to Router-A.
What needs to be done to prevent user traffic disruption in this scenario?

Q198. Which CLI command verifies if a switch’s CPU utilization is affecting network performance?

Q199. Which CLI command displays the status of all DHCP relay configurations?

Q200. Which CLI command enables 802.1X authentication on an Aruba CX switch port?