View All JN0-364 Actual Exam Questions Answers and Explanations for Free Aug-2026 [Q64-Q80]

Rate this post

View All JN0-364 Actual Exam Questions Answers and Explanations for Free Aug-2026

The Most In-Demand Juniper JN0-364 Pass Guaranteed Quiz

Juniper JN0-364 Exam Syllabus Topics:

Section	Objectives
MPLS and Service Provider Technologies	– MPLS fundamentals 1. Label switching and forwarding 2. LDP operations – VPN services 1. Layer 2 VPN overview 2. Layer 3 VPN concepts
BGP and Routing Policy	– Routing policy control 1. Route filtering and manipulation 2. Import/export policies – BGP fundamentals 1. Attributes and path selection 2. eBGP and iBGP operations
OSPF and IS-IS Routing Protocols	– OSPF configuration and troubleshooting 1. Areas and LSAs 2. Adjacency and neighbor states – IS-IS operation in service provider networks 1. LSP and SPF calculation 2. Levels and routing hierarchy
Troubleshooting and Operations	– Performance and monitoring 1. System logging and alarms 2. Traffic analysis basics – Network troubleshooting methodology 1. Protocol verification tools 2. Junos operational commands
Service Provider Architecture & Junos Fundamentals	– Service provider network design basics 1. Core, edge, and access architecture 2. Scalability considerations – Junos OS routing fundamentals 1. Junos CLI and configuration hierarchy 2. Routing table and forwarding concepts

Q64. You are designing a high availability solution for a Juniper router with dual Routing Engines (RE).
You want to ensure that the routing protocol state is preserved during an RE switchover. You have already enabled graceful Routing Engine switchover (GRES) and you want to avoid relying on helper routers to maintain the routing protocol state.
In this scenario, which feature would accomplish this behavior?

bidirectional forwarding detection

non-stop active routing

graceful restart

non-stop active bridging

Q65. You have configured graceful RE switchover (GRES), however you cannot complete the show system switchover command.
Referring to the exhibit, what is the problem?

The command is only available if non-stop routing is enabled.

The command is only available on the backup Routing Engine.

The command is only available If a backup router is configured.

The command is only available If graceful restart is enabled.

Q66. By default, which routing table contains a list of all ingress LSPs?

inet.0

inet.1

inet.2

inet.3

Q67. Which feature allows Junos OS to perform recursive lookups for static route next hops?

discard

resolve

reject

next-table

Q68. Referring to the exhibit, which statement is correct?

R1 will advertise only the 10.200.2.0/24 prefix to the 192.168.1.5 neighbor.

R1 will advertise only the 10.200.3.0/24 prefix to the 192.168.1.5 neighbor.

R1 will advertise the 10.200.1.0/24, 10.200.2.0/24, and 10.200.3.0/24 prefixes to the 192.168.1.5 neighbor.

R1 will advertise only the 10.200.1.0/24 prefix to the 192.168.1.5 neighbor.

Q69.

Referring to the exhibit, which protocol would automatically create a full mesh of label-switched paths between MPLS-enabled routers?

LDP

BFD

BGP

RSVP

Q70. Which term describes the router where traffic enters an MPLS label-switched path (LSP)?

egress router

transit router

penultimate router

ingress router

Q71. Which configuration selling prohibits a static route from being redistributed by a dynamic routing protocol?

route-filter

no-readvertise

qualified-next-hop

passive

Q72. What are three extension headers supported by IPv6? (Choose three.)

protocol

hop-by-hop options

header checksum

destination options

fragment

Q73. How are routing loops prevented in internal BGP networks?

Internal BGP routes are never readvertised to other internal BGP neighbors.

External BGP routes are never readvertised to other external BGP neighbors.

Internal BGP routes are never readvertised to other external BGP neighbors.

External BGP routes are never readvertised to other internal BGP neighbors.

Q74. You are the administrator for two Junos routers called R1 and R2. These two routers are directly connected to each other. These two routers run IS-IS and BFD. R1 is configured to send BFD packets every 300 milliseconds. R2 is configured to send BFD packets every 400 milliseconds. In this situation, what is the expected outcome?

Each router will send BFD packets at the rate that has been locally configured.

BFD will fail due to the mismatched timers.

Each router will negotiate to send BFD packets at the slowest of the two rates.

Each router will negotiate to send BFD packets at the fastest of the two rates.

Q75. Which statement describes integrated routing and bridging (IRB) interfaces?

An IRB interface Is an IP gateway For hosts of a bridge domain.

An IRB interface assigns interfaces to VLANs.

An IRB interface enables Layer 2 switching on the router.

An IRB interface defines a bridge domain.

Q76. Which IS-IS packet type will establish and maintain neighbor relationships?

link-state PDU

hello PDU

partial sequence number PDU

update PDU

Q77. Which LSA type does an OSPF ABR use to advertise external routes generated by an NSSAASBR into the backbone?

Type 5

Type 7

Type 3

Type 1

Q78. You configured an aggregated Ethernet bundle between R1 and R2. Unfortunately, the bundle is not working correctly.
Referring to the exhibit, which configuration change will solve this issue?

The LACP minimum links configuration should be changed to 2 on R1.

The LACP periodic mode should be changed to fast on R2.

The LACP mode should be changed to active on R1.

The LACP minimum links configuration should be changed to 1 on R2.

Q79. Which BGP attribute is used to detect routing loops?

AS path

MED

local preference

next hop

Q80. Exhibit:

Referring to the exhibit, R1 and R2 are configured to run IS-IS. The IS-IS adjacency between R1 and R2 is up. What does the output of the show isis interface command tell you about R1?