300-615 Premium Files Updated Jul-2023 Practice Valid Exam Dumps Question [Q49-Q73]

Rate this post

300-615 Premium Files Updated Jul-2023 Practice Valid Exam Dumps Question

Practice with 300-615 Dumps for CCNP Data Center Certified Exam Questions & Answer

Q49. Refer to the exhibit.

Interface fc1/5 is offline. Which action should be taken to troubleshoot the issue?

Activate the correct zoneset for VSAN 100.

Update the FLOGI database to contain the FLOGI entries for interface fc1/5 in VSAN 100.

Update the FCNs database to contain names for VSAN 100.

Configure the upstream ports and the server ports to be in VSAN 100.

Q50. Refer to the exhibit.

Interface fc1/5 is offline. Which action should be taken to troubleshoot the issue?

Activate the correct zoneset for VSAN 100.

Update the FLOGI database to contain the FLOGI entries for interface fc1/5 in VSAN 100.

Update the FCNs database to contain names for VSAN 100.

Configure the upstream ports and the server ports to be in VSAN 100.

Q51.

Refer to the exhibit. A network engineer traces the packet flow from the Veth991 of a blade server toward the core switch. The switch reports performance issues. What is the role of the interface Eth1/7?

IOM network interface

fabric interconnect uplink interface

IOM host interface

server interface

Q52. A firmware upgrade on a fabric interconnect fails. A bootflash contains a valid image. Drag and drop the recovery steps from the left onto the correct order on the right.

Q53. A firmware upgrade on a fabric interconnect fails. A bootflash contains a valid image. Drag and drop the recovery steps from the left onto the correct order on the right.

Q54. A mission-critical server is connected to site A.
Connectivity to this server is lost from site B because the MAC route is missing in the OTV VDC of the Nexus 7000 in site B due to MAC aging. Which action allows the flooding of the unknown unicast MAC on the Nexus 7000 in the OTV VDC?

Use route-map to advertise this MAC statically and redistribute with ISIS.

Unknown unicast flooding is not allowed.

Use the otv flood mac <> command to selectively flood traffic for a given MAC.

Use the otv isis bfd <> command to configure BFD protocol.

Q55. An engineer attempts to register Cisco UCS Manager to Cisco UCS Central, but the registration fails. The engineer can ping Cisco UCS Central from UCS Manager. Which two actions must the engineer attempt to resolve the problem? (Choose two.)

Synchronize the date and time to NTP for Cisco UCS Central and the Cisco UCS domains.

Apply the UCS Central license to UCS Central.

Place Cisco UCS Manager on the same subnet as Cisco UCS Central.

Allow port 443 between Cisco UCS Manager and Cisco UCS Central.

Allow port 9443 between Cisco UCS Manager and Cisco UCS Central.

Q56. Refer to the exhibit.

A Cisco UCS B-Series Blade Server is configured to boot from a shared storage via an iSCSI network. When a service profile is associated with the blade, the blade fails to attach the LUN. Which action resolves the issue?

Place VLAN 0 on the interface that connects to the storage

Implement a Layer 3 connection between the blade and the storage

Establish a Layer 2 connection between the blade and the storage

Q57. During a boot process of a Cisco UCS C-Series Rack Server, an engineer receives a “No Signal” message from the vKVM and physical connection. Which set of steps resolves the issue?

1- Disconnect the power cord
2- Confirm that all cards are property seated
3- Connect the power cord and power on the server

1- Power off the server and disconnect the power cord
2- Confirm that all cards are property seated
3- Connect the power cord and power on the server

1- Power off the server and disconnect the power cord
2- Confirm that all cards are available
3- Connect the power cord and power on the server

1- Disconnect the power cord
2- Confirm that all cards are properly seated
3- Connect the power cord

Q58. Refer to the exhibit.

When an engineer inserts 8-Gb FC SFP port 15 on a Cisco UCS Fabric Interconnect, the port fails. What is a possible cause of the issue?

Port 15 is configured as an Ethernet port.

Port 15 is configured for 4-Gb FC.

Port 15 is missing a license.

The polarity of the fiber cable is reversed.

Q59. Refer to the exhibit.

vPC between switch1 and switch2 is not working. Which two actions are needed to fix the problem? (Choose two.)

Match vPC domain ID between the two devices.

Configure IP address on the interface.

Activate VLANs on the vPC.

Configure vPC peer link and vPC peer keepalive correctly.

Configure one of the switches as primary for the vPC.

Q60. Refer to the exhibit.

The HSRP instance on both switches is showing as active. Which action resolves the issue?

Configure the HSRP timers to be the same.

Allow VLAN 100 between the switches.

Configure the IP address of N9K-B on the same subnet as N9K-A.

Configure preempt on only one of the switches.

Q61. An engineer must place a Cisco UCS B-Series Server in a single server pool in Cisco UCS Manager. The engineer creates a qualification policy, but the server is still seen in multiple pools. Which two actions resolve the issue? (Choose two.)

Select the Server Pool Policy Qualification from the qualification drop-down menu in the Server Pool Policy

Select the Server Pool Policy from the qualification drop-down menu in the Server Pool Policy Qualification

Set the operating system qualifier inside the Server Pool Policy Qualification

Set the number of vNICs qualifier inside the Server Pool Policy.

Set the storage capacity qualifier inside the Server Poo. Policy Qualification.

Q62. Refer to the exhibit. An engineer discovered a VFC interface in a down state on a Cisco Nexus Switch. Which action resolves the problem?

Change the cable between the switch and the server

Reset the Cisco Nexus port toward the file server

Update the CNA firmware and driver versions

Modify the fip keepalive message time to 30 seconds

Q63. A customer reports that the Chassis Management Controller fails to receive chassis information from Cisco UCS Manager. Which set of steps resolves the issue?

1) Verify that the IOM firmware and Cisco UCS Manager are at different software levels
2) Verify that at least two physical cables between the IOM and fabric interconnect function properly.
3) Check for runtime link down status
4) Reseat the affected IOM.

1) Verify that the IOM firmware and Cisco UCS Manager are at the same software level.
2) Verify that at least one physical cable between the IOM and fabric interconnect functions properly.
3) Check for runtime link down status
4) Reseat the affected IOM.

1) Verify that the IOM firmware and Cisco UCS Manager are at the same software level.
2) Verify that at least two physical cables between the IOM and fabric interconnect function properly.
3) Check for runtime link down status.
4) Reseat the affected IOM.

1) Verify that the IOM firmware and Cisco UCS Manager are at different software levels.
2) Verify that at least one physical cable between the IOM and fabric interconnect functions properly.
3) Check for runtime link down status.
4) Reseat the affected IOM.

Q64. An engineer is troubleshooting issues in Cisco UCS Director. Drag and drop the possible causes from the left onto the correct issues on the right.

Q65. An engineer is troubleshooting issues in Cisco UCS Director. Drag and drop the possible causes from the left onto the correct issues on the right.

Q66.

Refer to the exhibit. When an engineer inserts 8-Gb FC SFP port 15 on a Cisco UCS Fabric Interconnect, the port fails. What is a possible cause of the issue?

Port 15 is configured as an Ethernet port.

Port 15 is configured for 4-Gb FC.

Port 15 is missing a license.

The polarity of the fiber cable is reversed.

Q67. Refer to the exhibit.

The EEM script overrides all events in the system policy. What should be added to the script to resolve the issue?

event statement

environment variable

event-default action statement

configure terminal action

Q68. During a boot process of a Cisco UCS C-Series Rack Server, an engineer receives a “No Signal” message from the vKVM and physical connection. Which set of steps resolves the issue?

1- Disconnect the power cord
2- Confirm that all cards are property seated
3- Connect the power cord and power on the server

1- Power off the server and disconnect the power cord
2- Confirm that all cards are property seated
3- Connect the power cord and power on the server

1- Power off the server and disconnect the power cord
2- Confirm that all cards are available
3- Connect the power cord and power on the server

1- Disconnect the power cord
2- Confirm that all cards are properly seated
3- Connect the power cord

Q69. Refer to the exhibit.

The HSRP configuration in the exhibit fails to function. Which action resolves this issue?

Enable IP redirects.

Set the MTU to 1500 bytes.

Configure HSRP version 2.

Configure the same HSRP group on both devices.

Q70. Refer to the exhibit.

Refer to the exhibit. An engineer discovered a VFC interface in a down state on a Cisco Nexus Switch. Which action resolves the problem?

Change the cable between the switch and the server

Reset the Cisco Nexus port toward the file server

Update the CNA firmware and driver versions

Modify the fip keepalive message time to 30 seconds

Q71. Refer to the exhibit.

A network engineer is implementing an RBAC on the Cisco Nexus 9000 Series Switch. The role called Host A fails to clear LACP counters on the port channel 20. Which configuration resolves the issue?

Permit rule number 3 and read-write L3 operation.

Delete rule 3 and create new rule 3 to allow the permit command.

Change the sequence of rule 2 and rule 3.

Delete rule 2 and create a new rule 4

Q72. Refer to the exhibit.

Sw1 and Sw2 are two Cisco Nexus 9000 Series Switches that run Cisco NX-OS. They are VTEPs in the same vPC domain. Which statement describes what happens in this scenario?

Sw1 drops all traffic because there is no (S, G) OIF list to encapsulate VXLAN multicast packets and send them out to the underlay network through the uplink interfaces.

Sw1 performs the VxLAN multicast encapsulation and decapsulation for all traffic associated with the VxLAN VNIs.

Sw1 and switch 2 perform the VxLAN multicast encapsulation and decapsulation for all traffic associated with the VxLAN VNIs, depending on the hashing.

Sw2 did not send an IP PIM register to the rendezvous point for the multicast group of the VXLAN VNI.

Q73. Refer to the exhibit.

The HSRP instance on both switches is showing as active. Which action resolves the issue?